跳至主要内容

HENYED New mini dual USB inverter 300w

HENYED New mini dual USB inverter 300w

The  pictures as below:
300w Mini type


The features:
1. The use of single-chip digital control program, each product voltage, frequency, protection points are basically the same.
2. The input side has positive and negative reverse protection, the inverter does not work, re-connect correctly, the inverter is working properly..
3. Truly short circuit protection, you can short-circuit countless times, works well when connect correct.
4. 300W can withstand 3000W or even more power load impact, play a very good overload protection as well.
5. No-load voltage and full load voltage changes in the range of ± 5V on output voltage.
6. Different load, different input voltage frequency range of ± 1Hz
7. Dual USB 2.1A + 2.1A, you can charge IPHONE, IPAD and other high current devices.Intelligent identification of charging current.
8. At full load, work a few hours after the test inverter's temperature around 40-45 ℃ .
9. 300W can take 29-inch CRT old TV
10. 300W can bring 250W LED lights, energy saving lamps
11. With powerful power tools, electrician, electric saw, soya-bean milk maker, grinding machine, etc., and the inverter and equipment will not be damaged
12. After single-chip program processing, perceptual peak power instantaneous up to 3 times the amount of power





标签：

评论

发表评论

此博客中的热门博文

Does 2000W car inverter can load kettle to boil water?

I have buy a 2000W inverter. Does it can load kettle to boil water? 1. There is no problem with boiling water. The inverter is plugged into the cigarette lighter or directly connected to the battery, and then converts the 12V or 24V battery voltage to 110V or 220V ac output. As long as the power of the appliance does not exceed the power of the inverter, it can be used normally. 2. But we must also note that due to the use of the car's battery, the battery's loss of electricity is more serious, exacerbating the damage of the battery. In order to charge the battery as quickly as possible, the magneto will work harder and the vehicle will consume more fuel. The increase is related to the degree of your electricity use. Moreover, boiling water is actually equivalent to a large resistor, which generates high heat when the current passes through the resistor. This will cause more damage to the battery. So although it can be used to boil water, try not to do it as often as possib...
发表评论
阅读全文

How to use the inverter?

The inverter is a DC to AC transformer. In fact, the converter is a voltage inversion process. The converter is to convert the AC voltage of the power grid into a stable 12V DC output, but the inverter is to convert the 12V DC voltage output by the Adapter to a high-frequency AC voltage; the same applies to the pulse widths used in both parts. Modulation (PWM) technology. The core part is a PWM integrated controller, Adapter UC3842, inverter uses TL5001 chip. TL5001 operating voltage range 3.6 ~ 40V, its internal error amplifier, a regulator, oscillator, PWM control with dead-zone control, low-voltage protection circuit and short circuit protection circuit. 1. Input interface part: Input part has 3 signals, 12V DC input VIN, working enable voltage ENB and Panel current control signal DIM. VIN is provided by the Adapter. The ENB voltage is provided by the MCU on the motherboard. The value is 0 or 3V. When ENB=0, the inverter does not work, while at ENB=3V, the inverter is in no...
发表评论
阅读全文

HOW does an inverter work？

The inverter is a DC to AC transformer, and it is actually a process of conversion is a voltage inverter. AC converter is the voltage of the grid into a stable 12V DC output, while the output of the inverter is the Adapter 12V DC voltage into a high voltage alternating current high frequency; the same two parts are used with more than the width modulation (PWM) technique. Its core is an integrated PWM controller, Adapter using UC3842, the inverter is used TL5001 chip. TL5001 operating voltage range of 3.6 ~ 40V, which features an internal error amplifier, a regulator, oscillators, with dead-controlled PWM generator, low-voltage protection circuit and short circuit protection circuit and so on. Input interface part: There are three signal input section, 12V DC input VIN, work ENB enable voltage and current Panel control signal DIM. VIN provided by the Adapter, ENB voltage provided by the MCU on the motherboard, its value is 0 or 3V, when ENB = 0, the inverter does not work, and ENB = ...
发表评论
阅读全文