跳至主要内容

HOW does an inverter work？

The inverter is a DC to AC transformer, and it is actually a process of conversion is a voltage inverter.
AC converter is the voltage of the grid into a stable 12V DC output, while the output of the inverter is the Adapter 12V DC voltage into a high voltage alternating current high frequency; the same two parts are used with more than the width modulation (PWM) technique. Its core is an integrated PWM controller, Adapter using UC3842, the inverter is used TL5001 chip. TL5001 operating voltage range of 3.6 ~ 40V, which features an internal error amplifier, a regulator, oscillators, with dead-controlled PWM generator, low-voltage protection circuit and short circuit protection circuit and so on.
Input interface part: There are three signal input section, 12V DC input VIN, work ENB enable voltage and current Panel control signal DIM. VIN provided by the Adapter, ENB voltage provided by the MCU on the motherboard, its value is 0 or 3V, when ENB = 0, the inverter does not work, and ENB = 3V, the inverter is in normal working condition; and the DIM voltage provided by the motherboard, which ranges between 0 ~ 5V, different DIM PWM controller values ​​back to the feedback terminal of the inverter to the load current will be different, the smaller the value of DIM, the inverter output current greater.
Inverter
Inverter Atlas
Voltage startup circuit: ENB is high,
Output high voltage to light Panel backlight lamps.
PWM Controllers: has the following functions: internal voltage reference, an error amplifier, oscillator and PWM, overvoltage protection, undervoltage protection, short circuit protection, output transistors.
DC conversion: pulse and the MOS switch voltage conversion circuit consisting of the inductor, after the input MOS transistor push-pull amplifier as switching operation of the drive, so that the DC voltage of charge and discharge the inductor, so that the other end of the inductor can be obtained AC Voltage.
LC oscillator circuit and output: to ensure the 1600V voltage required to start the lamp and the lamp after starting the voltage down to 800V.
Output voltage feedback: When the load operation, the feedback voltage sampling, I play a stabilizing role in the inverter output voltage.

评论

发表评论

此博客中的热门博文

Does 2000W car inverter can load kettle to boil water?

I have buy a 2000W inverter. Does it can load kettle to boil water? 1. There is no problem with boiling water. The inverter is plugged into the cigarette lighter or directly connected to the battery, and then converts the 12V or 24V battery voltage to 110V or 220V ac output. As long as the power of the appliance does not exceed the power of the inverter, it can be used normally. 2. But we must also note that due to the use of the car's battery, the battery's loss of electricity is more serious, exacerbating the damage of the battery. In order to charge the battery as quickly as possible, the magneto will work harder and the vehicle will consume more fuel. The increase is related to the degree of your electricity use. Moreover, boiling water is actually equivalent to a large resistor, which generates high heat when the current passes through the resistor. This will cause more damage to the battery. So although it can be used to boil water, try not to do it as often as possib...
发表评论
阅读全文

How to use the inverter?

The inverter is a DC to AC transformer. In fact, the converter is a voltage inversion process. The converter is to convert the AC voltage of the power grid into a stable 12V DC output, but the inverter is to convert the 12V DC voltage output by the Adapter to a high-frequency AC voltage; the same applies to the pulse widths used in both parts. Modulation (PWM) technology. The core part is a PWM integrated controller, Adapter UC3842, inverter uses TL5001 chip. TL5001 operating voltage range 3.6 ~ 40V, its internal error amplifier, a regulator, oscillator, PWM control with dead-zone control, low-voltage protection circuit and short circuit protection circuit. 1. Input interface part: Input part has 3 signals, 12V DC input VIN, working enable voltage ENB and Panel current control signal DIM. VIN is provided by the Adapter. The ENB voltage is provided by the MCU on the motherboard. The value is 0 or 3V. When ENB=0, the inverter does not work, while at ENB=3V, the inverter is in no...
发表评论
阅读全文

How to adjust the output voltage on pure sine wave inverter 12v 220v 2000w if th...

How to adjust the output voltage on our pure sine wave inverter 12v 220v 2000w if the output voltage is lower or exceed the standard range. Generally, we will adjust the voltage according to customer requirements before shipment. if the voltage exceeds or is lower than the normal voltage range, the reference video wlll help you. Remarks: 1. Measure the voltage must use RMS , otherwise the error would be great. 2. must be carried out under the guidance of professionals.
发表评论
阅读全文